This presentation contains information about the project "The future of transportation... and how we'll pay for it" by Joseph L. Schofer, Department f Civil & Environmental Engineering. The presentation was delivered at the 40th Anniversary Seminar Day at Northwestern University on April 18, 2009.
This study tested a dynamic traffic assignment (DTA) model as a tool for pre-planning strategies for managing major freeway incidents. Incidents of varying scale and duration were modeled in the northern Chicago highway network, and the impacts of incidents and response actions were measured in terms of both lane-mile-hours of...
The mission of the Infrastructure Technology Institute is to develop strategies and tools
to protect and improve the condition, capacity and performance of the nations highway, railroad,
and mass transit infrastructure systems. The Institute does this through the development
and deployment of (1) advanced technologies for structural health monitoring, (2)...
This presentation provides information on the project "Safety Concrete - a Material Designed to Fail" by Jeffrey J. Thomas, Julie Gevrenov, Hamlin Jennings, and Edward O'Neil. The presentation was delivered at the 106th Annual Meeting & Exposition of The American Ceramic Society, Indianapolis, Indiana in 2004.
Few would argue that concrete is an important and useful material: after all, concrete is the backbone of the world’s infrastructure, used in vast amounts to make roads, buildings, bridges, and other structures. But sometimes familiarity breeds contempt. To most people, concrete is simply that boring grey stuff that we...
The objective of this program is to measure the changes in the properties of the C-S-H gel phase in cement paste as a function of the Ca/Si ratio. The motivation is to better understand the hydration products that form in blended cements with lower Ca/Si ratios than portland cement. The...
This presentation provides information on the progress report of the project "Empirical Study of Life-Cycle Cost Analysis for Bridges" by Ahmad Hadavi, 2003.
This final report provides information about TEA-21 [Transportation Equity Act for the 21st Century] funded projects designated A433, and A495 "Evaluation of Capacity of Micropiles Embedded in Dolomite". The report was submitted to the Infrastructure Technology Institute at Northwestern University by Richard J. Finno on September 20, 2002.
Non-destructive evaluation (NDE) techniques have been used for a number of years to provide quality control of construction procedures for drilled shafts and driven concrete piles. In particular sonic echo and impulse response methods have been used extensively to check lengths and continuity of newly-installed foundations. In recent years, the...
An empirical procedure for fitting a complementary error function (erfc) to settlement and lateral ground movement data in a direction parallel to an excavation support wall is proposed based on extensive optical survey data obtained around a 12.8 m excavation in Chicago. The maximum ground movement and the height and...
Several three-dimensional effects were observed in the performance monitoring data collected during excavation for the Ford Engineering Design Center (FEDC) in Evanston, Illinois. These responses are related to lateral deformations of the soil around the excavation walls, forces in the cross-lot and diagonal bracing that supported the temporary wall and...
This paper presents the results of 159 finite element simulations conducted to define the effects of excavation geometry, i.e., length, width and depth of excavation, wall system stiffness, and factor of safety against basal heave on the 3-dimensional ground movements caused by excavation through clays. The results of the analyses...
Successful use of monitoring data to update performance predictions of supported excavations depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the inverse analysis techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors...
Two numerical procedures are described that quantitatively identify a set of constitutive parameters that best represents observed ground movement data associated with a deep excavations in urban environments. This inverse problem is solved by minimizing an objective (or error) function of the weighted least-squares type that contains the difference between...
Performance monitoring of deep excavations typically includes slope inclinometers, optical surveying of soil deformation, tiltmeters and strain gages. Current monitoring data collection and processing requires time consuming site visits and manual data reduction by project engineers. Development of robotic and remote access geotechnical instrumentation conceptually allows processed data to be...
This paper describes developments of integrated tools for predicting, monitoring, and controlling ground movements associated with excavations in urban areas. Successful use of monitoring data to update performance predictions of supported excavations depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the...
This presentation provides information on the the project "Use Of High-Performance A710 Grade B Steel in Construction of Lake Villa, IL Bridge". The presentation was delivered by Morris E. Fine, Semyon Vaynman, and Nunzio Mario Biondolillo on June 14, 2006.
This final report contains information on years 6-7-8 (2004-2007) of TEA-21 funded projects designated A487, W420, and A212. The report was submitted by Morris E. Fine and Semyon Vaynman in 2007.
During the past several years an easily weldable, high strength (more than 75 ksi yield), high impact fracture toughness steel (NUCu steel) has been investigated at Northwestern University with bridge applications in mind. For good weldability without pre-heating and post-heating, the carbon content of the steel was kept low and...
Northwestern University developed copper-precipitation-hardened, high-performance weathering steel (NUCu 70W Steel) that is produced by hot rolling after casting and then air-cooling. Due to simple processing the steel is fabricated at lower cost than competing high-performance steels that require quench and tempering. NUCu 70W steel can be easily welded without pre-...
This brochure contains information on the NUCu Steel ASTM A-710 Grade B project published at Northwestern University's Infrastructure Technology Institute with the support of the Illinois Department of Transportation. The brochure includes further explanation to Current and Potential Applications, Chemical Composition and Steel Processing, Mechanical and Fracture Properties, Corrosion, Welding,...
Northwestern University developed copper-precipitation-hardened, high-performance weathering steel (NUCu 70W Steel) that is produced by hot rolling after casting and then air-cooling. Due to simple processing the steel is fabricated at lower cost than competing high-performance steels that require quench and tempering. NUCu 70W steel can be easily welded without pre-...
Experimental Time Domain Reflectometry (TDR) data obtained from the field are compared with numerical simulations using a finite-difference solution of the transmission line equations. The model simulates transmission of a voltage pulse along a lossy coaxial cable where deformities on the cable, such as crimps and shears, are represented by...
How can gatekeeping theory in the circulation of cultural objects, including knowledge production, inform the way cultural sociology investigates the role of the producer and the cultural object as “gated” entities? Using the case of producers working under the rubric of “Contemporary African art” to investigate opportunities and restrictions to...
In his essay on Mali, Bruce Whitehouse of Lehigh University shows how failures of elected leaders, state institutions, and external donors can shift power to the streets and an uncertain contest among armed forces.
This presentation is intended to provide background on the principles involved in geotechnical and infrastructure applications of Time Domain Reflectometry (TDR). TDR is basically radar in which a voltage pulse is launched along a coaxial cable. A reflection of the voltage pulse occurs at every location where the cable is...
Time Domain Reflectometry (TDR) is a versatile technology amenable to a variety of measurements and nondestructive monitoring of infrastructure conditions. It can be utilized to monitor deformation of soil/rock and structures, monitor changes in fluid levels, and monitor water content of soils. Furthermore, this monitoring can be automated using systems...
Two longwall coalmine panels were mined at a depth of approximately 156 m (510 ft) beneath I-70 east of Washington, Pennsylvania such that it crossed the width of one panel at two locations. The Pennsylvania Department of Transportation (PennDoT) assumed responsibility for real time monitoring of both ground deformation and...
This paper reviews the new field of geo-measurement with metallic cable time domain reflectometry (TDR) for surveillance of transportation facilities. TDR is radar in a coaxial cable, and is especially advantageous for remote monitoring because of its inherently digital nature. Advances can be separated into those that leverage use of...
This thesis combines field and laboratory measurements with three dimensional (3D) finite element analysis (FEM) to demonstrate the use of Time Domain Reflectometry (TDR) cable-grout composites to measure localized shearing in soft soil. Past field installations of TDR cable-grout composites in rock have lead to its widespread use in the...
This thesis presents the application of Time Domain Reflectometry technology in nine case studies. Presented in detail are cable and grout installation techniques, data acquisition instrumentation and autonomous real time monitoring of soil deformation using TDR. The goal of this work is to summarize the state of the technology in...
This file contains the poster on "Wireless Data Acquisition System in Autonomous Crack Monitoring Projects" from Crossbow Smart Dust Challenge created by Mat Kotowsky, Hasan Ozer, and David Kosnik.
This file contains power-point slides of Application to Crossbow’s Smart Dust Challenge Contest, title "Wireless Data Acquisition System" by Mat Kotowsky and Hasan Ozer. The presentation was delivered at University of California, Berkeley on February 11, 2005.
This paper describes qualification of devices to measure sub micro-meter changes in crack width, which is the basis of autonomous crack monitoring for control of blasting vibrations. Performance of LVDT, eddy current and potentiometer sensors to monitor long-term and transient displacements will be described. Potentiometers are attractive for wireless measurement,...
Miniaturized, wireless instrumentation is now a reality and this thesis describes development of such a system to monitor crack response. Comparison of environmental (long-term) and blast-induced (dynamic) crack width changes in residential structures has lead to a new approach to monitoring and controlling construction vibrations. In wireless systems transducer power...
Mining near the town of Blanford, Indiana for a number of years has led to an opportunity for Peabody Coal Company to study and compare environmental and blast effects. Such a comparison allows description of any blast effects relative to those caused by common environmental changes, which should be familiar...
Public concern over construction vibration-induced cracking has led to the development of a radically new approach to vibration, an autonomous crack comparometer (ACC). This thesis chronicles the first step of developing equipment and software necessary for this system. The new system will automatically compare longterm weather induced micrometer changes in...
The thesis describes the second phase of development of the Autonomous Crack Comparometer (ACC) system to incorporate measurements of ground motions and add several changes in the autonomous operation. In order to obtain the ground motion and air blast data, four additional transducers have been added. There are now a...
Construction is omnipresent in modern-day America. It's the sound and vibration of a nation scrambling to keep up with its burgeoning population. In most states, allowable construction-induced ground motions range from 0.5 to 1.0 inches per second (in/sec) and under certain
conditions up to 2.0 in/sec.
However, ground motion as...
This thesis consists of the data and analysis of structural responses for two different studies: the Office of Surface Mining (OSM) study of the velocity response of “atypical” residential structures and the Autonomous Crack Monitoring (ACM) study. The main basis of this thesis was to do additional analysis on a...
This appendix synthesizes micrometer changes in crack width in response to both long term (environmental) and transient (blast vibration) of four of the structures in the main body. The appendix begins with a description of the genesis of the study and instruments employed. Response of the distressed wood-framed structure in...
Autonomous Crack Measurement (ACM) facilitates simultaneous measurement of crack response to environmental changes and vibrations produced by various construction activities. Dual-purpose crack displacement sensors measure crack response, while the vibration environment is defined by standard seismological transducers and the weather environment is defined as changes in temperature and humidity. This...
All structures have cosmetic cracks, which have no influence on structural integrity and usually remain unremarked until the structure’s occupants sense ground vibrations. Such vibrations are often associated with engineering activity, but are rarely responsible for cracks. However, this is difficult to prove without scientific basis. Automated Crack Monitoring (ACM)...
Cosmetic cracks are very common in structures, and most of the time they remain unnoticed and do not decrease the structural integrity. Although these cracks are unremarkable and barely noticeable, occupants become concerned about these cracks when construction occurs nearby. In order to investigate the true nature of these cracks,...
In early 2001, a sinkhole formed directly under State Road 66 near the city of Sebring in Highlands County, Florida. The Florida DOT built a land bridge over the sinkhole and the road was reopened to traffic. Since SR-66 is an important regional trucking route, it was decided that the...
Crack and structural response to construction trench blasting was measured in a woodframe house with a stucco exterior. Blasts at distances between 232 m to 368 m produced peak particle velocities (PPV) and air blast over pressures (AB) of 9 mm/sec and 0.02 kPa (123 dB), respectively. Structural response velocities...
This thesis summarizes two further developments of the Autonomous Crack Monitoring (ACM) system, which facilitates simultaneous measurement of crack response to environmental changes and various dynamic events. The first component was measurement of crack responses in three different materials and locations in a residential structure subjected to ground vibrations produced...
This thesis summarized the qualification and testing of two commercial Autonomous Crack Monitoring (ACM) systems for use in measuring micrometer displacement of cracks. Qualification involved the assessment of both laboratory and field performance in a residential structure subjected to nearby quarry blasting for the production of roadway aggregate. Aggregate and...
A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brick work. The dynamic environment was unusual. Even though the blasting...
Micro-meter dynamic crack responses in a two story structure to rock blasting- and wind gust- excitation are compared to those induced by long term climatological effects. These measurements substantiate the conservancy of the 12.5 mm/s (0.5 in./s) blasting vibration control to protect residential structures against cracking. The test structure was...
This paper describes the technology and methods deployed in the continuous autonomous remote monitoring of cracks in interior and exterior walls of a residence near a limestone quarry. The object is to quantitatively compare crack response to blast-induced ground motion to that induced by diurnal temperature changes, weather fronts, and...